 |
DUDE BUSTER: NB12, NB58, NB34, NB78, NB1, NB118, NB114; “BUST THEIRS, NOT YOURS.” Seven sizes of High Impact Deep Sockets (allows the bolt to travel over 7”, deepest on the market) for tightening or breaking nuts. The ½” Drive End and the Socket End are CAST with S-5 Striking Steel, then HEAT TREATED for SUPERIOR STRENGTH. The ends are then FUSED onto pipe and become a single piece unit (no breaking points) that is fully balanced so there is no wobble (easier on the impact and the user). Each size is marked with dimensional nut size and bolt size. De- signed to be used and abused for Heavy Impact Work with air or electric impacts. |
 |
ALL-IN-ONE DUDE: AD1; “The coolest tool yet.” It’s a Chuck Key that fits most of the ½” Jacobs chucks. The large handle gives the user leverage to really tighten down on the bits. The handle is also a Blade Wrench that fits all the Worm Drive saws and most of the Sidewinder type. Insert the chuck key into the hole of a blade to easily pop out the diamond for the worm drive saw. No more trying to knock the diamond out with the claw of a hammer and bending the blade. More importantly, it has a bottle opener that will fit just about any bottle cap on the market. A real lifesaver. The tool is cast of one-piece high strength steel and then heat-treated. It is harder than any of the materials it is used with. Casting is used for the consistent precision needed for the chuck key and blade wrench. After inspection it is dipped in corrosion resistant oil and then packaged with instructions on how to use all the components (the bottle opener is never questioned). Tool weight is 10 oz. |
 |
DON’T SLIDE DUDE: DSD1; No-skid bumper ring for Hitachi NR83A2 Nail gun. Easily fits over the rear cap of the nail gun. Keeps the tool from sliding off the sloped roof sheeting when gun is put down. Protects the gun from bumps when it is passed down by the airline. Talk about “BRIGHT ORANGE”, you will see this from a mile away. (So can the forklift driver). Tool weight is 6 oz. |
 |
SCREW BUSTER: SB38, SB38X3PACK, SB716, SB916, SBSET3; “Makes screwing fun again.” The 3/8” impact socket is designed to drive the SDS screws for the hold down systems. Sold singly – 5 oz. or in a 3 pack – 16 oz. The 7/16” is for 1/4” bolt size lag screws and the 9/16” is for 3/8” bolt size lag screws, 6 oz each. The combo set weights about 20 oz. Cast of S-5 striking steel and heat-treated, these precision made ½” Drive Impact Sockets are as rugged as the NUT BUSTER; but, just a little smaller. |
 |
DUDEVERSAL EXTENSION: DUE12; A ½” Drive Impact Universal Joint makes this 30” extension the best companion to any socket. The DUDEVERSAL allows the user to get into tight places by letting the impact tool be outside of the wall as well as work at an angle. A Real Back Saver by letting the users stand instead of bending over the work. Works great with ZONE 4 hardware and manufactured shear-walls (Strong-Wall, Shear Max, etc). Tool weight is 4.5 lbs. |
 |
DUDE BUSTER WRENCH: NBW12, NBW58, NBW34, NBW78, NBW1, NBW118, NBW114; “Power in your hand.” Seven sizes of 12-point wrenches that allow the bolt to travel thru the cast head so the wrench won’t drop off the nut. Cast with High Strength Steel for precision of the socket, the handle is welded to the head and then the wrench is sent to Heat Treating to make it the toughest wrench out there. The 12-point socket allows the user to work in tight areas (excellent with the HARDY panel) and still get lots of leverage on the hard to turn bolts. A big padded handle makes the tool comfortable on the roughest hands and is angled so that knuckles won’t rub. Tool weight: NBW12 & NBW58 - (16 oz); NBW34, NBW78 & NBW1 - (20 oz); NBW118 & NBW114 - (26 oz) |
 |
FORM BUSTER III & MINI FORM BUSTER FORM BUSTER III: FORMBUSTER3; “Break all Barriers.” 5’ Heavy Duty Pry Bar with a Fulcrum point cast into the blade for extra leverage. Knuckle Saver at the end of the longest handle on the market to protect hands. Blade made of High Strength Heat Treated Steel for heavy lifting, with V notch in blade for pulling pins/nails. Neck on the blade extends into the handle at the stress point of extra strength. Blade is 3” wide X 12” long. Tool weight is 16 lbs. |
 |
DUDE HICKEY & MINI DUDE HICKEY DUDE HICKEY: DH34; Dude Hickey & big brother DH48; Long Dude Hickey, bend #’s 3,4, and 5 rebar if you’re tough enough (both will accept up to #8 bar and have the strength to bend it, if you do). 32” or 48” handles (longer than all others on market) for extra leverage, but still get you into tight places. Cast, one-piece head is Heat Treated for superior strength with no weld points to break. 3” neck extends into handle so there is no stress/breakage point. Big handle grip for comfort and control. Go ahead and use a cheater bar if you need, DUDE HICKEY can take it. Tools weight 8 lbs. and 10.5 lbs. |
 |
BUCKET CART: BUCKETCART; “Don’t carry it! Cart it!” Heavy Duty just begins to describe the capability of this workhorse. The Bucket Cart is rated at over 300 lbs. carrying capacity and designed for a standard 5 gallon plastic bucket. What you put into it is left up to you (steel stakes, release agents, baseballs, fishing gear, tools…), but whatever you decide, the cart can carry it. Tool weight is 14.5 lbs. |
 |
BOLT MARXSTER: BM1; Bolt Marxster hand held bolt marker incorporates all the suggestions from framers to make their job easier. The body is made of heavier grade steel so the tool won’t break down after just a few uses. The marking pins are spring loaded to retract back so they are not interfering with production. They are pointed making an easy to see mark and an easy start for the auger bits. Designed to mark X4 and X6 bottom/sill plates. Nice molded handle for comfort and secure grip during the workday. Tool weight is 24 oz. |
 |
REBAR DUDES: RB2E; Straightens nos. 3 & 4 bar with heads at 45 degrees at the end of a 30” ribbed handle for better grip and leverage. (4.25 lbs.) RBMINI; 18” long for straightening no.3 bar with a strong steel head and ribbed handle. Great for pool jobs and is pouch sized. (2.75lbs.) RBD24; Bends nos. 3 & 4 bar with a strong steel head and a 24” long ribbed handle for better grip and leverage (3.25lbs.) RBD30; Bends nos. 3 & 4 bar with a strong steel head and a 30” ribbed handle for better grip and more leverage. (4lbs.) RBD4590; Straightens nos. 3 & 4 bar with heads at 45 and 90 degree angles on a 32” long ribbed handle for better grip and lots of leverage. (5 lbs.) (Handles made with no. 6, grade 60 rebar for maximum strength) |
 |
DUDE DRIVER: DD324; Post driving has never been more fun. Tapered handles for better grip and less fatigue and a larger barrel (3” across compared to 2” & 2-1/2”) so mushroom ends won’t stick. The drive in the Dude Driver is a 2.5 lb. solid steel cap welded tight in its 24” long body so what you drive is going down. Tool weight is 22 lbs. |
 |
BOLT MARXSTER TALL DUDE: BMTD; “Leave your mark in the right place.” Tall Dude allows the worker to stand and mark the bolts. The base is made from channel steel to resist bending and keep the accuracy of the tool. The marking pin is spring loaded to retract the pin from the work and to keep the users hand from being pinched between the weighted handle and the shaft (OUCH). With the marking pin secured in the shaft, it won’t slide out and get bent in the back of the truck or lost. The bottom plate has bold reference stripes enabling the user to make precise marks (no running back and forth, drilling out holes to get the wall to drop). Tool weight is 3 lbs. |
 |
FDS24P; 24" Fat Dude Shooter ain't no ordinary P-Shooter. Its spring-loaded drive shaft allows the nail to set down into the tube making for one hand operation (pointing up). You won't pinch your hand between the handle and the tube(that's neat)! Why Fat? Because we put a hefty 2 1/2 lb. handle on the drive shaft so you can sink a 16d in just a couple of whacks. (Great for poured in place wall framing) Tool weight is 3.5 lbs. FDS36 & FDS42 36"/42" Fat Dude Shooters have all the benefits of their little brother, but allow user to have a better reach into high rafters and between joist where you can't get a hammer or nail gun or maybe you just don't want to get out the ladder. Tool weight 4.25# |
 |
ELECTRA CART: ELECTRACART; Designed by electricians for electricians. It will carry up to (4) four spools of wire to the job site and the electrician will be able to pull the wire as well. Easily converts back to standard Bucket Cart with a holder for the wire rod. (Shocking how long it took to come up with this great idea) Extra legs in front give the Electra cart the stability it needs for pulling wire. Tool weight is 20.5 lbs. |
 |
DUDE DUSTER: DDSB; “Blows sawdust away from the blade line like MARIAH blows tumbleweed off the plains.” A small, lightweight attachment to the front of the SKIL/BOSCH 77 SAWS turns your exhaust air into a tornado to keep the cut line clear of debris. Just one existing screw on the back of your blade guard holds this little dynamo to the saw. Tool weight is 2 oz. |
 |
DUDE STAKE DRIVER: DSDRF; Holds round, flat and square stakes so the tool takes the blow, not the stake, reducing the mushrooming affect. With a big 3” round steel plate top, this gives the user a bigger target to hit. The handle keeps the user hand/wrist away from the strike zone for safety. Tool weight is 2.25 lbs. |
 |
LAZY DUDE WHEELBARROW KIT: LDK1; “3 Wheels are better than 1.” Adds two big 10” wheels to the wheelbarrow for stability with heavy loads. Works on all types of terrain. Universal mounting for all types and brands of wheel- barrows. Tool weight is 13 lbs. |
 |
HARDY-DUDE BUSTER: HD78, HD118; “You still BUST THEIRS, NOT YOURS!” These rugged little guys are built as tough as the DUDE BUSTERS, but are only 5” long to fit into the Hardy panel and other tight places. Only two sizes, the nuts on 7/8” bolts or 1-1/8” bolts. Yes they are YELLOW in color, but they are not chicken to do hard work. Tool weight is 3 lbs. |
 |
BOLT BUSTER: BB30; the Bolt Buster allows the user to straighten up to ¾” diameter bolts without having to bend down/over or attach a nut and hit with a hammer possibly damaging the threads. The 30” long handle comes with an oversized grip for comfort and control. Makes the job quick and clean. Tool weight is 4 lbs. |
 |
DUDE HOOKER: DHH1; “Don’t be left hanging.” Skyhook for Hitachi NR83A Nail gun. Quickly attaches to the back of the tool so you can hang your gun on a 2X rafter. Left-handed? No problem, the DUDE HOOKER fits either way for your comfort and you don’t have to turn your gun up side down to fit it onto a rafter. Bright orange of course for added visibility. Tool weight is 16 oz. |
 |
DUDE SAW PONY: DSP22; “Is the toughest critter on the job.” Just slip a 2X into the top U bracket and tack and you have one of the strongest worktops out there. Made of 2x2 angle and braced with #4 rebar, this A frame is designed to take the heavy loads. The feet are round so the user does not cut or scratch themselves. Can be used solo or as a pair. Tool weight is 12 lbs.each. |
 |
SIMPSON-DUDE BUSTER: SD34, SD1; Yes indeed, “You still BUST THEIRS, NOT YOURS!” Designed for the Heavy Hex Nuts supplied with the Simpson Strong-tie steel panels; makes installation quick and clean. Only two sizes for the 1-1/4” nut that fits on a 3/4” bolt and the 1-5/8” nut that fits on the 1” bolt. They are GOLD in color to celebrate Simpson’s 50th anniversary. They are worth their weight and they are GOLD! Tool weight is 2.5 lbs. |
 |
DUDE NAIL BUSTER & REPLACEMENT OAK HANDLE DUDE NAIL BUSTER: DNB24, DNB24S; “The Spirit of a Patriot with the ATTITUDE of the DUDE.” These sweet swinging hammers are precision cast from S-5 striking steel for durability and balance. Check out the details. Our star pattern on both sides of the head commemorates nine/eleven (count ‘em). These hammers get ‘ER done. An 18” straight ax handle has a great grip with a knob at the handle base to give your swing a SNAP. Available in both milled and smooth faces for rough or finish carpentry. Weight is 31 oz. |
 |
FORM BUSTER WHEEL KIT: FBWK3; This kit makes the FORM BUSTER III so easy to move around on most surfaces. The kit comes complete with all the parts you need. Included are two double ball bearing wheels with heavy-duty washers, grade 8 hex bolt, and Stover nut; so it locks, but can be removed and reused. The kit gives the FORM BUSTER III over 500 lbs. of lifting capacity. Great for moving heavy equipment and other big dudes. This kit also fits the MINI FORM BUSTER. Tool weight is 22 oz. |
 |
SAW BUSTER caddys all makes of saws for ease of cutting. No need to get on your knees for excellent control of the saw. Very versitile with handle extensions so you can reach anywhere. |
 |
Specialy designed to be used and abused for HEAVY IMPACT WORK with all 3/4" anvil air or electric impact tools. This heavy "dudey" socket is outfitted with the bolder 3/4" Drive, but is only 2-1/4" long; perfectly sized for attaching or removing 1-1/8" tilt-up brace bolts. |